DXLOG og Virtuellt nettverk i med Hamachi i MULTI OP

Published: Monday, 04 October 2021

DXLOG NETTVERK Hamachi / virtuelt Nettverk

 

HAMACHI SETUP

Hamachi VPN-klient Hvis du ikke allerede har gjort det;

 Last ned Hamachi – VPN-klient, installèr.  eller denne via Dropbox https://www.dropbox.com/s/cy2h88foxl0d1bn/hamachi_2015.msi?dl=0

Denne bruker vi for å få alle MULTI OP-stasjonene i samme nettverk.

1. Du lager et nettverk og bestemmer passord. Dette nettverket får da en offisiell ID f eks. 123-456-789 passord kan være radioamator1

2. I Hamachi kan to gå til Network -> Join An Existing Network" .

3. Skriv inn ID 123-456-789 passord kan være radioamator1

 

 

 How to setup Network in N1MM?

a) Choose Multi-Unlimited

b) enable Network window

c) enable network via LAN or via WAN (Hamachi)

d) Setup account in Hamachi

e) create network in Hamachi

f) join a network

 

 

Nettverk for MULTI OP

Velg 

1. Enable Network "Network is enabled"

Enable or disable station networking
Text command: NETON or NET and NETOFF or NONET

NB. If you intend to use the number server for SO2R or in a multi-station setting it is not sufficient to only enable the network.
A network interface (UDP or client/server TCP) must also be enabled in the network configuration panel (see above).

1. Option -> Velg Network Enabled

 

2. Configure Network

Sett opp SERVER

Vanligvis kan man sette opp nettverk via:

- en lokal switch

- Hamachi Virtuelt nettverk - i MESH NETT

- Softethernet Virtuelt nettverk

HAMACHI SERVER i DXLOG på NETTVERK konfigurasjon

SERVER / Hoved PC

NB! 25.75.94.139 er din egen PC som er SHACK SERVER eller MASTER LOGG PC

 

 

2. Klient

koble til som klient.

1 stk  per stasjon.

Nummer server

I noen contester så bruker man serienummer.

I klasser som :

- Multi Single

- Multi 2 med en stasjon som RUN + en stasjon som Inband på samme bånd

- Single operatør med 2-3 stasjoner som SO2R-SO3R etc. DVS en dxlog per PC

Velg

"USE Number Server"

Nummer server kan også benyttes i contester som feks.  Månedstest, SAC test, CQ WPX SSB/CW og Russian DX contest

 

 How to setup Network in DXLOG?

http://dxlog.net/docs/index.php/Configuration#Contest_configuration 

DX Log

1. Guide ( her)

2. New Log

3. Velg SAC SSB

4. Multi Op - Multi-Transmitter

5. Option -> Enable Network , answer YES! 

 

Server

6. Configure Network

6.0 Station ID: SERVER

6.1 Start Network server set 25.0.0.0 port: 9888

6.2 UDP Networking for multiple station IP adress:25.255.255.255 port 9888 

7.0  Configure Network

7.1 Station ID: RUN 1 eller 80m

7.2 eller Connect as Client. 

  

It's quite easy...

You need to setup on of stations as Server, and two others as clients.

So, in case you have three stations, let's say STN1, STN2 and STN3...
In case that STN1 is server, you need to do the following:

Go to Options->Configure network... click Start server checkbox and use
0.0.0.0 as Server IP...leave the port as default (9888)...
Set StationID to STN1 here...

That's it at server... now you need to know the ip address of the server...
for example let say it is 192.168.0.50...

On other two stations:

In Options->Configure network...
Set StationID to STN2 and STN3.
Click Connect as client checkbox and set the ip address bellow that
checkbox to the IP address of the server (192.168.0.50 in example)..

And that's it..

Create/Open log file at all three PC's and enable network (click on
Options->Network is enabled)..

And you will see all three stations in Status window (ALT+J), plus there
will be info in main status bar (bottom of DXLog.net window)..


 

Hits: 85